130
edits
Changes
Add timer switch info and fix oopsies on pinouts that dont match
* <s>Document the theory of operation and create a rough block diagram for functionality.</s> Shown in the manual
* Document any theories, issues that arise and their fixes, as well as things to watch out for
* Potentially design Design a new tone decoder daughterboard using more common components(LM567)* Recreate timer PCB to allow for additional signals to be added to models without extra timers* Design and add a small audio amplifier circuit and speaker to listen to the recevier audio feed locally(LCRx only)
<br />
====DIP Switch Config====
----
=====SW1 (Total Time)=====
The stock DIP switch config for the steady 3 min cycle timer is, from left to right (Up = ON): up, down, up, down, down, up, down, up. This sets pins 1, 3, 6 and 8 high, and 2,4,5,and 7 low (the DIP switch numbers are backwards in reference to the IC pins). This equates to a RC time constant of 165.
According to the manual, SW1 controls the total time that the function is activated with a +/- 10% margin. The switches add together in a binary sequence when closed (up)
<gallery>
At low values it seems to be pretty accurate (eg. 5 sec), but with my test of "180s" (8, 6, 5 and 4 high) yielded approximately 3m18s (almost 200s). Timing the stock setting gets 2m57s, or 177s.This is consistent with the stated +/- 10% margin.
'''U2''' - Motorola MC14011BCP<ref>https://www.mouser.com/datasheet/2/308/1/MC14001B_D-2315187.pdf</ref> (B-Series CMOS Quad 2−Input NAND Gate)
'''U3''' - NMotorola MC1455P1<ref>https:/A /www.onsemi.com/pdf/datasheet/mc1455-d.pdf</ref> (Populated on other boards555 Timer)[ONLY PRESENT ON CD CYCLE/FIRE MODELS]
'''U4''' - Maxim ICM7240IPE<ref>https://www.analog.com/media/jp/technical-documentation/data-sheets/1360.pdf</ref> (Programmable Timer/Counter IC)
|-
|'''P1-4'''
|??? Cancel "A" (Goes to STOP terminal on terminal block as well as P2-4 on decoder module B?from manual)
|-
|'''P1-5'''
!Function
|-
|'''P1P2-1'''
|GND
|-
|'''P1P2-2''' |N/C on Main BoardDecoder Cancel (from manual)
|-
|'''P1P2-3''' |Cancel "B" (Coupled to GND via C44)
|-
|'''P1P2-4''' |Cancel "C" (N/C on Main Board)
|-
|'''P1P2-5'''
|N/C on Main Board
|}
{|
|+ <U>'''LCRx Relay Driver Board Pinout'''</U>
|<div style="display: flex;">
<div>
!Function
|-
|'''P1P2-1'''
|GND
|-
|'''P1P2-2''' |Relay #1 Coil (E9 on I/O header)
|-
|'''P1P2-3''' |Relay #1 Coil (E10 on I/O header)
|-
|'''P1P2-4''' |N/C on Main BoardRelay #2 Coil (Optional in SC series, but traces route to it on driver boardnot used at all in LCRx.)
|-
|'''P1P2-5''' |N/C on Main BoardRelay #2 Coil (Optional in SC series, but traces route to it on driver boardnot used at all in LCRx.)
|}
</div>
!Function
|-
|'''P1P2-1'''
|GND
|-
|'''P1P2-2'''
|5th tone filter (J2)
|-
|'''P1P2-3'''
|6th tone filter (J1)
|-
|'''P1P2-4'''
|N/C
|-
|'''P1P2-5'''
|N/C
|}
!Function
|-
|'''P1P2-1'''
|GND
|-
|'''P1P2-2'''
|N/C
|-
|'''P1P2-3'''
|Transformer AC in
|-
|'''P1P2-4'''
|N/C
|-
|'''P1P2-5'''
|Transformer AC in
|}
*Due to the XR2211A IC being obsolete and quite hard to source nowadays, I may try to design my own tone decoder board using the LM567 IC which is still available in SMD form factors. The LM567 also outputs a logic low when signal is detected, but the design will have to incorperate a LDO 5v regulator to power the chip from the 12v the cards get.
*I have not adjusted any of the filter components on the receiver circuit yet, but I did run an experiment by leaving the device plugged in with the antenna attached inside my house while sending the activation signal from a few dense suburban blocks away. The board operated perfectly with 5W from my Anytone 878, turning on and off.
*While the tone filters are labled J1 thru J6 on the PCB, the actual numbering is reversed, tone filter 1 is at the top and 6 is at the bottom. Despite that, my unit (and I suspect others that were reconfigured by a third party) may not start at slot 1. My unit has slots 6, 5, and 4 occupied with the corresponding wiring on the programming board. The nameplate implies slots 1, 2, and 3 however. Overall it doesn't ''really'' matter if things aren't in numerical order, but it sure as hell makes things confusing...
*On the maxon data radio DB-15 connector, you can solder a normal speaker to pin
<br />