Difference between revisions of "DFM-17 Radiosonde"

From RECESSIM, A Reverse Engineering Community
Jump to navigation Jump to search
(Added IC Table and began to populate, added image with U ref designators assigned)
(Filling out IC table with U9-U12 information)
Line 50: Line 50:
  
 
==Identified Supplementary IC's==
 
==Identified Supplementary IC's==
'''V719''' = [https://www.mouser.com/datasheet/2/389/stg719-1850635.pdf STG719STR Low Voltage 4 Ohm SPDT Switch]
 
 
'''C22A''' = [https://www.ti.com/lit/ds/symlink/lmv762.pdf LMV761 Low Voltage Precision Comparator with Push/Pull Output]
 
 
'''636EE''' = [https://www.mouser.com/datasheet/2/427/dg636e-1766306.pdf DG636EEQ Siliconix/Vishay Dual SPDT Switch]
 
 
'''LW053A''' = [https://www.ti.com/lit/ds/symlink/sn74lv4053a.pdf Triple 2 Channel Analog Multiplex/Demultiplexer]
 
 
<br />
 
 
{| class="wikitable"
 
{| class="wikitable"
 
|+
 
|+
!Ref Desig(s)
+
IC Part Numbers and Markings
 +
!
 
!Manufacturer
 
!Manufacturer
 
!Part Number
 
!Part Number
 
!Description
 
!Description
 +
!Package
 
!Part Marking
 
!Part Marking
 
!Datasheet
 
!Datasheet
Line 73: Line 66:
 
|ARM MCU, 24MHz, 8KB RAM, 64KB Flash
 
|ARM MCU, 24MHz, 8KB RAM, 64KB Flash
 
|
 
|
 +
|ARM 32F100R8T6B
 
|[https://www.mouser.com/datasheet/2/389/stm32f100cb-1851080.pdf Mouser]
 
|[https://www.mouser.com/datasheet/2/389/stm32f100cb-1851080.pdf Mouser]
 
|-
 
|-
Line 79: Line 73:
 
|STG719
 
|STG719
 
|STG719STR Low Voltage 4 Ohm SPDT Switch
 
|STG719STR Low Voltage 4 Ohm SPDT Switch
 +
|SOT-23-6
 
|V719
 
|V719
 
|[https://www.mouser.com/datasheet/2/389/stg719-1850635.pdf Mouser]
 
|[https://www.mouser.com/datasheet/2/389/stg719-1850635.pdf Mouser]
Line 87: Line 82:
 
|0.3 pC Charge Injection, 100 pA Leakage
 
|0.3 pC Charge Injection, 100 pA Leakage
 
CMOS ± 5 V / 5 V / 3 V Dual SPDT Analog Switch
 
CMOS ± 5 V / 5 V / 3 V Dual SPDT Analog Switch
 +
|
 
|636EE
 
|636EE
 
|[https://www.mouser.com/datasheet/2/427/dg636e-1766306.pdf Mouser]
 
|[https://www.mouser.com/datasheet/2/427/dg636e-1766306.pdf Mouser]
 
|-
 
|-
|U7
+
|U8
 
|Texas Instruments
 
|Texas Instruments
 
|SN74LV4053A
 
|SN74LV4053A
 
|Triple 2-Channel Analog Multiplexer/Demultiplexer
 
|Triple 2-Channel Analog Multiplexer/Demultiplexer
 +
|SOT-23-6
 
|LW053A
 
|LW053A
 
|[https://www.ti.com/lit/ds/symlink/sn74lv4053a.pdf Texas Instruments]
 
|[https://www.ti.com/lit/ds/symlink/sn74lv4053a.pdf Texas Instruments]
 
|-
 
|-
|U8
+
|U9
 
|Texas Instruments
 
|Texas Instruments
 
|LMV761
 
|LMV761
 
|Low Voltage Precision Comparator with Push/Pull Output
 
|Low Voltage Precision Comparator with Push/Pull Output
 +
|
 
|C22A
 
|C22A
 
|[https://www.ti.com/lit/ds/symlink/lmv762.pdf Texas Instruments]
 
|[https://www.ti.com/lit/ds/symlink/lmv762.pdf Texas Instruments]
|-
 
|U9
 
|
 
|
 
|
 
|
 
|
 
 
|-
 
|-
 
|U10
 
|U10
 +
|Silicon Labs
 +
|Si4063
 +
|High Performance, Low Current Transmitter
 
|
 
|
|
+
|40632A C01Q81
|
+
|[https://www.silabs.com/documents/public/data-sheets/Si4063-60-C.pdf Silcon Labs]
|
 
|
 
 
|-
 
|-
 
|U11
 
|U11
 +
|u-Blox
 +
|MAX-M8C-0-10
 +
|u-blox M8 GNSS module, ROM, crystal
 
|
 
|
|
+
|MAX-M8C-0-10
|
+
|[https://www.u-blox.com/sites/default/files/MAX-M8-FW3_DataSheet_%28UBX-15031506%29.pdf u-Blox]
|
 
|
 
 
|-
 
|-
 
|U12
 
|U12
|
+
|STMicroelectronics
|
+
|M24LR04E-R
|
+
|Dynamic NFC/RFID tag IC with 4-Kbit EEPROM,
|
+
 
|
+
energy harvesting, I²C bus and ISO 15693 RF interface
 +
|TSSOP8 (DW)
 +
|4BEB 8150
 +
|[https://www.st.com/resource/en/datasheet/m24lr04e-r.pdf STMicroelectronics]
 
|-
 
|-
 
|U13
 
|U13
Line 137: Line 133:
 
|
 
|
 
|
 
|
 +
|33R
 
|
 
|
 
|-
 
|-
 
|U14
 
|U14
 +
|
 
|
 
|
 
|
 
|
Line 151: Line 149:
 
|
 
|
 
|
 
|
 +
|DVL
 
|
 
|
 
|-
 
|-
 
|U16
 
|U16
 +
|
 
|
 
|
 
|
 
|
Line 161: Line 161:
 
|-
 
|-
 
|U17
 
|U17
 +
|
 
|
 
|
 
|
 
|

Revision as of 23:51, 16 January 2023

The DFM-17 is a balloon-launched radiosonde manufactured by GRAW Radiosondes GmbH & Co. KG, and used for meteorological sounding.

The label side view of a DFM-17 Radiosonde


Overview

The DFM-17 radiosonde succeeds the DFM-09 radiosonde. Graw began a contract with NOAA in the US to provide radiosondes. As of Late 2021, several sites have made the transition as part of NOAA’s Operational Test and Evaluation (OT&E) program. 45 CONUS sites are expected to use these radiosondes in early 2022. [1]

Specs [2]

  • Weight: 63g
  • Size: 90 x 67 x 44 mm
  • Power supply: 2 CR123A batteries
  • Estimated runtime: ~240 minutes
  • Transmission rate: 1 packet/sec
  • Bandwidth: ~10 kHz (Website lists <12)
  • Frequency range: 400 - 405.99 MHz
  • Modulation: GFSK
  • TX Power: ~100mW
  • Error Correction: Code-spreading, interleaving
  • SoC: STM32F100R8T6B, 24MHz, 8KB RAM, 64KB Flash
  • GPS: U-Blox MAX-M8C-0-10
  • Transmitter: Si4063

Peripheral attachment points

LED's and Buttons

  • Button = PC8
  • LED_Y = PC7
  • LED_G = PC6
  • LED_R = PB12

GPS

  • PA3(RX) = GPS TXD
  • PA2(TX) = GPS RXD

UART via USB Port

  • PA9(TX) = USB D+
  • PA10(RX) = USB D-

Si4063

  • PB2 = CS/nSEL
  • PA7 = SDI
  • PA6 = SDO
  • PA5 = SCLK

Identified Supplementary IC's

IC Part Numbers and Markings
Manufacturer Part Number Description Package Part Marking Datasheet
U1 STMicroelectronics STM32F100R8T6B ARM MCU, 24MHz, 8KB RAM, 64KB Flash ARM 32F100R8T6B Mouser
U2, U3, U4, U5, U7 ST STG719 STG719STR Low Voltage 4 Ohm SPDT Switch SOT-23-6 V719 Mouser
U6 Vishay DG636E 0.3 pC Charge Injection, 100 pA Leakage

CMOS ± 5 V / 5 V / 3 V Dual SPDT Analog Switch

636EE Mouser
U8 Texas Instruments SN74LV4053A Triple 2-Channel Analog Multiplexer/Demultiplexer SOT-23-6 LW053A Texas Instruments
U9 Texas Instruments LMV761 Low Voltage Precision Comparator with Push/Pull Output C22A Texas Instruments
U10 Silicon Labs Si4063 High Performance, Low Current Transmitter 40632A C01Q81 Silcon Labs
U11 u-Blox MAX-M8C-0-10 u-blox M8 GNSS module, ROM, crystal MAX-M8C-0-10 u-Blox
U12 STMicroelectronics M24LR04E-R Dynamic NFC/RFID tag IC with 4-Kbit EEPROM,

energy harvesting, I²C bus and ISO 15693 RF interface

TSSOP8 (DW) 4BEB 8150 STMicroelectronics
U13 33R
U14
U15 DVL
U16
U17


Photos

Disassembly


  1. Examine rope, parachute and parachute rigging lines for viability. Neatly organize the flight rigging if usable. Discard if not viable for reuse.
  2. Cut the zip tie surrounding the Styrofoam from the top portion by the rope loop.
  3. Pull the rope loop out, there should be little to no resistance.
  4. Make a slice in the sticker[4] where the two pieces of Styrofoam meet.
  5. Pull apart the two Styrofoam pieces to reveal the circuit board.
  6. Pull the circuit board out. There will be some resistance.
  7. The board is now separated from the Styrofoam shell, reuse if desired.
  8. Pull the two CR123A batteries out, keep or discard them. The board can run off USB power. Batteries are not necessary for development on this board.

Reassembly


  1. Insert two fresh CR123A batteries into the board.
  2. Line up the board to the IO cutouts in the Styrofoam, begin to push into the slots. Make sure the antenna wire comes through.
  3. Press the top piece of Styrofoam into place.
  4. Tape or apply another sticker onto the back label. (Optional)
  5. Insert the plastic rope loop piece.
  6. zip tie the shell together, the zip tie end should end up on the edge nearest to the power button.
  7. Rope on a balloon/drone/kite/etc.. to the rope loop.
  8. Power on the device by pressing and holding the button, you will see a yellow light blink, hold until the light turns solid.

Mini USB Port

The mini USB port on the board does not use the USB protocol for communication, it is a UART bus. However using USB to power the board should not harm the board in theory.

In order to use it, splice a USB cable and wire up a USB<->TTL adapter with the following pins:

  • VBUS: 5 Volts DC
  • D-: TX
  • D+: RX
  • GND: GND


The board will communicate with the official GRAWMET software using this approach. Reverse engineering of the port's protocol is underway, however it is believed to use a similar, if not the same protocol the PS-15 uses.

Hardware modifications

MrARM's modified DFM-17 with a SWD connector and a SMA antenna.

The DFM-17 has solder pads for an SMA port and a SWD header.

An Adafruit Skinny SWD SMT connector and a generic SMA connected was used in the photo.





Developing and Programming the board

A very crude diagram showing the standard SWD pinout overlaid onto the DFM-17 board


When lab testing, you can power the board from the USB header. It also appears to run fine supplying 3.3V to the SWD port(STLink clones do this).


The board uses a STM32, and requires a ST-Link to program. The process used to upload code to the MCU is the same as the Vaisala RS41 radiosonde, you will need to solder and connect the VTRef(3.3V), Ground, SWDIO, SWDCLK and RST pins to your ST-Link.

The board can run without external power being supplied when programming. This board has read-out protection enabled similar to the RS41 and this must be disabled before you can flash firmware to the board.