DFM-17 Radiosonde

The DFM-17 is a balloon-launched radiosonde manufactured by GRAW Radiosondes GmbH & Co. KG, and used for meteorological sounding.

The label side view of a DFM-17 Radiosonde

Overview

The DFM-17 radiosonde succeeds the DFM-09 radiosonde. Graw began a contract with NOAA in the US to provide radiosondes. As of Late 2021, several sites have made the transition as part of NOAA’s Operational Test and Evaluation (OT&E) program. 45 CONUS sites are expected to use these radiosondes in early 2022.

Specs

• Weight: 63g
• Size: 90 x 67 x 44 mm
• Power supply: 2 CR123A batteries
• Estimated runtime: ~240 minutes
• Transmission rate: 1 packet/sec
• Bandwidth: ~10 kHz (Website lists <12)
• Frequency range: 400 - 405.99 MHz
• Modulation: GFSK
• TX Power: ~100mW
• Error Correction: Code-spreading, interleaving
• SoC: STM32F100R8T6B, 24MHz, 8KB RAM, 64KB Flash
• GPS: U-Blox MAX-M8C-0-10
• Transmitter: Si4063

Peripheral attachment points

LED's and Buttons

• Button = PC8
• LED_Y = PC7
• LED_G = PC6
• LED_R = PB12

GPS

• PA3(RX) = GPS TXD
• PA2(TX) = GPS RXD

UART via USB Port

• PA9(TX) = USB D+
• PA10(RX) = USB D-

Si4063

• PB2 = CS/nSEL
• PA7 = SDI
• PA6 = SDO
• PA5 = SCLK

Identified Supplementary IC's

V719 = STG719STR Low Voltage 4 Ohm SPDT Switch

C22A = LMV761 Low Voltage Precision Comparator with Push/Pull Output

636EE = DG636EEQ Siliconix/Vishay Dual SPDT Switch

LW053A = Triple 2 Channel Analog Multiplex/Demultiplexer

Ref Desig(s)	Manufacturer	Part Number	Description	Part Marking	Datasheet
U1	STMicroelectronics	STM32F100R8T6B	ARM MCU, 24MHz, 8KB RAM, 64KB Flash		Mouser
U2, U3, U4, U5, U7	ST	STG719	STG719STR Low Voltage 4 Ohm SPDT Switch	V719	Mouser
U6	Vishay	DG636E	0.3 pC Charge Injection, 100 pA Leakage CMOS ± 5 V / 5 V / 3 V Dual SPDT Analog Switch	636EE	Mouser
U7	Texas Instruments	SN74LV4053A	Triple 2-Channel Analog Multiplexer/Demultiplexer	LW053A	Texas Instruments
U8	Texas Instruments	LMV761	Low Voltage Precision Comparator with Push/Pull Output	C22A	Texas Instruments
U9
U10
U11
U12
U13
U14
U15
U16
U17

Photos

• 

  Internal view of the DFM-17

• 

  The bottom side of the PCB in the DFM-17

• 

  The label sticker NOAA(US) puts on the back of their DFM-17 radiosondes

• 

  A view of the DFM-17 Radiosonde showing both layers to better assist tracing connections while reverse engineering the hardware.

• 

  Possible meanings of the internal labels and values. The date code in particular which may be useful to date production times. NWS sondes have the same cryptic string printed on the outside of the sonde where the mfg. date normally is on other countries'. "TU" may just indicate the board comes with sensors according to a third party source.

• 

  Pinout of the DFM-17 sensor stalk. Not all pins are used, and some seemingly are connected to a trace but end abruptly.

• 

  V719 SOIC packages removed as well as 636EE (SPDT Switch) and LW053A (Mux/Demuxer)

• 

  Mapping of the pins on the sensor stalk to the connector and their corresponding IC/IO lines. Top of sensor stalk corresponds to bottom of pictured connector!

• 

  Back of the DFM PCB without CR123A battery holders

• 

  Top of PCB with U(*) Reference Designators overlaid ICs

Disassembly

1. Examine rope, parachute and parachute rigging lines for viability. Neatly organize the flight rigging if usable. Discard if not viable for reuse.
2. Cut the zip tie surrounding the Styrofoam from the top portion by the rope loop.
3. Pull the rope loop out, there should be little to no resistance.
4. Make a slice in the sticker where the two pieces of Styrofoam meet.
5. Pull apart the two Styrofoam pieces to reveal the circuit board.
6. Pull the circuit board out. There will be some resistance.
7. The board is now separated from the Styrofoam shell, reuse if desired.
8. Pull the two CR123A batteries out, keep or discard them. The board can run off USB power. Batteries are not necessary for development on this board.

Reassembly

1. Insert two fresh CR123A batteries into the board.
2. Line up the board to the IO cutouts in the Styrofoam, begin to push into the slots. Make sure the antenna wire comes through.
3. Press the top piece of Styrofoam into place.
4. Tape or apply another sticker onto the back label. (Optional)
5. Insert the plastic rope loop piece.
6. zip tie the shell together, the zip tie end should end up on the edge nearest to the power button.
7. Rope on a balloon/drone/kite/etc.. to the rope loop.
8. Power on the device by pressing and holding the button, you will see a yellow light blink, hold until the light turns solid.

Mini USB Port

The mini USB port on the board does not use the USB protocol for communication, it is a UART bus. However using USB to power the board should not harm the board in theory.

In order to use it, splice a USB cable and wire up a USB<->TTL adapter with the following pins:

• VBUS: 5 Volts DC
• D-: TX
• D+: RX
• GND: GND

The board will communicate with the official GRAWMET software using this approach. Reverse engineering of the port's protocol is underway, however it is believed to use a similar, if not the same protocol the PS-15 uses.

Hardware modifications

MrARM's modified DFM-17 with a SWD connector and a SMA antenna.

The DFM-17 has solder pads for an SMA port and a SWD header.

An Adafruit Skinny SWD SMT connector and a generic SMA connected was used in the photo.

Developing and Programming the board

A very crude diagram showing the standard SWD pinout overlaid onto the DFM-17 board

When lab testing, you can power the board from the USB header. It also appears to run fine supplying 3.3V to the SWD port(STLink clones do this).

The board uses a STM32, and requires a ST-Link to program. The process used to upload code to the MCU is the same as the Vaisala RS41 radiosonde, you will need to solder and connect the VTRef(3.3V), Ground, SWDIO, SWDCLK and RST pins to your ST-Link.

The board can run without external power being supplied when programming. This board has read-out protection enabled similar to the RS41 and this must be disabled before you can flash firmware to the board.