17
edits
Changes
Jump to navigation
Jump to search
== Reassembly ==*VBUS: 5 Volts DC*D-: TX*D+: RX*GND: GND
# Insert two fresh CR123A batteries into the board.
# Line up the board to the IO cutouts in the Styrofoam, begin to push into the slots. Make sure the antenna wire comes through.
# Press the top piece of Styrofoam into place.
# Tape or apply another sticker onto the back label. (Optional)
# Insert the plastic rope loop piece.
# zip tie the shell together, the zip tie end should end up on the edge nearest to the power button.
# Rope on a balloon/drone/kite/etc.. to the rope loop.
# Power on the device by pressing the button.
Added possible LD series LDO data sheet
<br />
== Overview ==
The DFM-17 radiosonde succeeds the DFM-09 radiosonde. Graw began a contract with NOAA in the US to provide radiosondes. As of Late 2021, several sites have made the transition as part of NOAA’s Operational Test and Evaluation (OT&E) program. 45 CONUS sites are expected to use these radiosondes in early 2022. <ref>[https://www.graw.de/news/press/graw-delivers-to-usa-noaanational-weather-service/ GRAW delivers to USA NOAA/National Weather Service]. GRAW Radiosondes GmbH & Co. KG. Retrieved 17 November 2021.</ref>
<br />
== Specs <ref>https://www.graw.de/products/radiosondes/dfm-17/</ref> ==
* Weight: 63g* Size: 90 x 67 x 44 mm* Power supply: 2 CR123A batteries* Estimated runtime: ~240 minutes* Transmission rate: 1 packet/sec* Bandwidth: ~10 kHz (Website lists <12)* Frequency range: 400 - 405.99 MHz* Modulation: GFSK* TX Power: ~100mW* Error Correction: Code-spreading, interleaving* SoC: STM32F100R8T6B, 24MHz, 8KB RAM, 64KB Flash* GPS: Ublox U-Blox MAX-M8C-0-10 * Transmitter: Si4063 ==Peripheral attachment points== ====LED's and Buttons==== *Button = PC8*LED_Y = PC7*LED_G = PC6*LED_R = PB12 ====uBlox GPS (USART_2)==== *PA3(RX) = GPS TXD (Pin 2)*PA2(TX) = GPS RXD (Pin 3)*PB8 = GPS 1pps (Pin 4) (LED next to flex cable connector) ====UART via USB Port (USART_1)==== *PA9(TX) = USB D+*PA10(RX) = USB D- ====Si4063 (SPI_1)==== *PB2 = CS/nSEL (Pin 15)*PC3 - SDN (Pin 1)*PA7 = SDI (Pin 14)*PA6 = SDO (Pin 13)*PA5 = SCLK (Pin 12) '''NFC/RFID 4k EEPROM''' *PC13 = RF WIP/Busy (Pin 7)*PB6 = SCL (Pin 6)*PB7 (''needs confirmed, signal routes under STM)'' = SDA (Pin 5) '''STG719 (DPST) - U2''' *PC11 = IN (Pin 1) '''STG719 (DPST) - U3''' *PD2 = IN (Pin 1) '''STG719 (DPST) - U4''' *PB5 = IN (Pin 1) '''STG719 (DPST) - U5''' *PB4= IN (Pin 1) '''DG636 (Dual DPST) - U6''' *VDD = ENABLE (always HIGH) (Pin 2)*PA10 = A0 (Pin 1)*''UnknownPin#1'' (routes under STM) = A1 (Pin 14) '''STG719 (DPST) - U7''' *''UnknownPin#1'' (routes under STM) = IN (Pin 1) '''SN74LV4053 (Triple 2Ch Mux/Demux) - U8''' *PB13 & PB14 = A (Pin 11)**STM pins connected by trace? ''Why? Read back?''*''UnknownPin#1'' (routes under STM) = B (Pin 10) & C (Pin 9)**IC pins connected by trace '''Analog Inputs to STM2''' *PA0 - Vbatt/Power supply voltage (''needs confirmation)''*PB1 - Vbatt/Power supply current monitor (''needs confirmation)''
<br />
==Identified Supplementary IC's==
<gallery>
File:DFM-17 Uref overlay.jpg|alt=U reference designators overlaid|Top view of PCB with U reference designators overlaid
</gallery>
{| class="wikitable"
|+
IC Part Numbers and Markings
!
!Manufacturer
!Part Number
!Description
!Package
!Part Marking
!Datasheet
!Note
|-
|U1
|STMicroelectronics
|STM32F100R8T6B
|ARM MCU, 24MHz, 8KB RAM, 64KB Flash
|LQFP48
|ARM 32F100R8T6B
|[https://www.mouser.com/datasheet/2/389/stm32f100cb-1851080.pdf Mouser]
|''Some recent batches of the DFM-17 have been using knockoff STM32s! The chip shortage strikes again!''
|-
|U2, U3, U4, U5, U7
|ST
|STG719
|STG719STR Low Voltage 4 Ohm SPDT Switch
|SOT-23-6
|V719
|[https://www.mouser.com/datasheet/2/389/stg719-1850635.pdf Mouser]
|''Analog ADG719 pin compatible equivalent?''
|-
|U6
|Vishay
|DG636E
|0.3 pC Charge Injection, 100 pA Leakage
CMOS ± 5 V / 5 V / 3 V Dual SPDT Analog Switch
|TSSOP14
|636EE
|[https://www.mouser.com/datasheet/2/427/dg636e-1766306.pdf Mouser]
|
|-
|U8
|Texas Instruments
|SN74LV4053A
|Triple 2-Channel Analog Multiplexer/Demultiplexer
|SOT-23-6
|LW053A
|[https://www.ti.com/lit/ds/symlink/sn74lv4053a.pdf Texas Instruments]
|
|-
|U9
|Texas Instruments
|LMV761
|Low Voltage Precision Comparator with Push/Pull Output
|SOT-23-6
|C22A
|[https://www.ti.com/lit/ds/symlink/lmv762.pdf Texas Instruments]
|
|-
|U10
|Silicon Labs
|Si4063
|High Performance, Low Current Transmitter
|QFN20
|40632A
C01Q81
2217|[https://www.silabs.com/documents/public/data-sheets/Si4063-60-C.pdf Silcon Labs]||-|U11|u-Blox|MAX-M8C-0-10|u-blox M8 GNSS module, ROM, crystal||MAX-M8C-0-10|[https://www.u-blox.com/sites/default/files/MAX-M8-FW3_DataSheet_%28UBX-15031506%29.pdf u-Blox]||-|U12|STMicroelectronics|M24LR04E-R|Dynamic NFC/RFID tag IC with 4-Kbit EEPROM, energy harvesting, I²C bus and ISO 15693 RF interface|UDFN8|4BEB 8150|[https://www.st.com/resource/en/datasheet/m24lr04e-r.pdf STMicroelectronics]|''Needs verification. DFM-17 does not boot when removed; I suspect the serial and calibration is stored in the EEPROM here - Trevor229''|-|U13|STMicroelectronics|LD series, ''unsure on specific part''|3.3V Low Drop Out Voltage Regulator|DFN6|33R|[https://www.mouser.com/datasheet/2/389/ld39050-1849494.pdf Possible part from Mouser]|''Needs verification, appears to provide 3.3V regulated power''|-|U14|||||||''Looks like a high side current monitor amplifier, need more information''|-|U15|ABLIC|S-8200A Series, ''unsure on specific Part Number''|BATTERY PROTECTION IC FOR 1-CELL PACK||VDL|[https://www.mouser.com/datasheet/2/360/S8200A_E-1365901.pdf Mouser]|''Needs verification, Potentially a Winsok WSTDW01 Battery Protection IC?''|-|U16|||||AL W24||''In-line with battery power, need more information; chip marking''|-|U17|||||||''Connected to USB data lines, likely a UART, isolation, and/or level shifter''|}<br /> == Photos ==
<gallery>
File:DFM-17 Internal.jpg|Internal view of the DFM-17
File:DFM-17 Battery Holder.jpg|The bottom side of the PCB in the DFM-17
File:DFM-17 NOAA Label.jpg|The label sticker NOAA(US) puts on the back of their DFM-17 radiosondes
File:Dfm17-2layers.png|A view of the DFM-17 Radiosonde showing both layers to better assist tracing connections while reverse engineering the hardware.
File:Label id speculaton.jpg|Possible meanings of the internal labels and values. The date code in particular which may be useful to date production times. NWS sondes have the same cryptic string printed on the outside of the sonde where the mfg. date normally is on other countries'. "TU" may just indicate the board comes with sensors according to a third party source<ref>https://sondehunt.de/language/en/archive/1189</ref>.
File:Sensor stalk pinout.jpg|Pinout of the DFM-17 sensor stalk. Not all pins are used, and some seemingly are connected to a trace but end abruptly.
File:V719 and others removed.jpg|V719 SOT-23-6 packages removed as well as 636EE (SPDT Switch) and LW053A (Mux/Demuxer)
File:Stalk pinout mapping.png|Mapping of the pins on the sensor stalk to the connector and their corresponding IC/IO lines. '''''<u>Top of sensor stalk corresponds to bottom of pictured connector!</u>'''''
File:Dfm back pcb no battery.jpg|Back of the DFM PCB without CR123A battery holders
</gallery>
== Disassembly ==<br /> #Examine rope, parachute and parachute rigging lines for viability. Neatly organize the flight rigging if usable. Discard if not viable for reuse.#Cut the zip tie surrounding the Styrofoam from the top portion by the rope loop.#Pull the rope loop out, there should be little to no resistance.#Make a slice in the sticker<ref>[[:File:DFM-17 NOAA Label.jpg|File:DFM-17 NOAA Label.jpg]]</ref> where the two pieces of Styrofoam meet.#Pull apart the two Styrofoam pieces to reveal the circuit board.#Pull the circuit board out. There will be some resistance.#The board is now separated from the Styrofoam shell, reuse if desired.#Pull the two CR123A batteries out, keep or discard them. The board can run off USB power. Batteries are not necessary for development on this board. ==Reassembly==
<br />
# Examine ropeInsert two fresh CR123A batteries into the board.#Line up the board to the IO cutouts in the Styrofoam, parachute and parachute rigging lines for viabilitybegin to push into the slots. Neatly organize Make sure the flight rigging if usable. Discard if not viable for reuseantenna wire comes through.# Cut the zip tie surrounding Press the top piece of Styrofoam from into place.#Tape or apply another sticker onto the top portion by back label. (Optional)#Insert the plastic rope looppiece. # Pull zip tie the rope loop outshell together, there the zip tie end should be little end up on the edge nearest to no resistancethe power button. # Make Rope on a slice in the sticker<ref>[[:File:DFM-17 NOAA Labelballoon/drone/kite/etc.jpg|File:DFM-17 NOAA Label.jpg]]</ref> where to the two pieces of Styrofoam meetrope loop.# Pull apart Power on the two Styrofoam pieces to reveal device by pressing and holding the button, you will see a yellow light blink, hold until the circuit boardlight turns solid.# Pull the circuit board out. There will be some resistance.# ==Mini USB Port==The mini USB port on the board is now separated from does not use the Styrofoam shellUSB protocol for communication, reuse if desiredit is a UART bus.# Pull However using USB to power the two CR123A batteries out, keep or discard them. The board can run off USB power. Batteries are should not necessary for development on this harm the boardin theory. In order to use it, splice a USB cable and wire up a USB<->TTL adapter with the following pins:
The board will communicate with the official GRAWMET software using this approach. Reverse engineering of the port's protocol is underway, however it is believed to use a similar, if not the same protocol the [https://www.graw.de/products/radiosondes/ps-15/ PS-15] uses. ==Hardware modifications== ====SMA Port to replace antenna & SWD header:====The DFM-17 has solder pads for an SMA port and a SWD header. An [https://adafru.it/4048 Adafruit Skinny SWD SMT] connector and a generic SMA connected was used in the photo. ====Minimizing transmit range:====As amateurs we are not licensed to transmit in the 400-406MHz band, so for testing purposes one should perform this mod. Unsolder the antenna wire and take two 100 ohm resistors and twist them in parallel, then solder them to the center pad and one of the side pads on the SMA footprint. This creates a 50 ohm dummy load for the Si4036 to transmit into. The range is reduced to a couple tens of feet. Also if you are running a radiosonde_auto_rx instance, don't forget to turn it off during testing to avoid feeding erroneous data to Sondehub!<gallery>File:Modified DFM-17 Radiosonde.jpg|MrARM's modified DFM-17 with a SWD connector and an SMA antenna portFile:Dfm 17 swd and resistors.jpg|Trevor229's DFM with ST-Link SWD pins connected to debug interface and 50 ohm dummy load mod.</gallery> == Developing and Programming the board ==
[[File:DFM-17 SWD Port pinout.png|thumb|A very crude diagram showing the standard SWD pinout overlaid onto the DFM-17 board]]
When lab testing, you can power the board from the USB header. It also appears to run fine supplying 3.3V to the SWD port(STLink clones do this).
The board uses a STM32, and requires a ST-Link to program. The process used to upload code to the MCU is the same as the Vaisala RS41 radiosonde, you will need to solder and connect the VTRef(3.3V), Ground, SWDIO , SWDCLK and SWDCLK RST pins to your ST-Link. The board can run without external power being supplied when programming. This board has read-out protection enabled similar to the RS41 and this must be disabled before you can flash firmware to the board. <br /><references />
