Difference between revisions of "Mechanical Tools"

From RECESSIM, A Reverse Engineering Community
Jump to navigation Jump to search
m (→‎Round edged scalpels: Removed some non-essential lines to tighten things up.)
Line 48: Line 48:
 
====Work piece holders for PCBAs with large TH (through hole) components====
 
====Work piece holders for PCBAs with large TH (through hole) components====
 
Fix me
 
Fix me
 +
 +
=== Magnification devices ===
 +
 +
==== Stereoscopic microscope (analog) ====
 +
 +
===== AmScope SM-4NTP =====
 +
This stereo microscope has a lockable double arm boom stand and a magnification range of 7X to 45X (zoom) and is great for component level repairs / modifications. The boom stand allows to quickly change between the normal view onto the work piece in the soldering fixture and a side-view while holding the work piece in the hand without the need to touch the focus and magnifications settings. You just pull out the head over the edge of the table to have room to turn the work piece in the hand to be able to get a side-view of pin-less IC-packages or other things that are difficult to see in the normal view.
 +
 +
Fix me: add photos
 +
 +
==== Stereoscopic microscope (digital) ====
 +
Fix me: add links and photos
 +
 +
===== The Stereo Ninja Project =====
 +
Fix me: add links and photos

Revision as of 11:06, 7 October 2023

Lathe and drill press

Grinders, Drills, Lathes, Milling Machines, Welders and any other tools used to modify hardware. If you used it while reverse engineering, list it here!

Tool Index


Essential tools and consumables for manipulating PCBAs (Printed Circuit Board Assemblies)

Soldering Irons

Knockoff JBC station with original JBC soldering tips

Fix me: Photos and text

Weller Station

Fix me: Photos and text

Tweezers

Manipulating PCBAs often involves handling small and/or hot components while soldering. Most types of tweezers are made of some kind of steel, which can make them susceptible to get magnetized, which is not ideal if that is not done intentionally by using a magnetize tool. This accidental magnetization can be avoided by using tweezers made of titanium. The minimal set of tweezers should consist of following types:

Straight, fine tweezers

Angled, fine tweezers

Straight, coarse tweezers with riffles

This type of tweezers come in handy when something has to be gripped securely in order to be able to bend / shape them in a controlled manner. These tweezers have a thick metal parts that are not easily bend out of shape like the fine tweezers.

Straight, self-holding tweezers

Scalpels

There are many types of straight edged and round edged scalpels beside the ones listed below. The one mentioned here are the essential types needed to attach botch wires and sniffing wires to signal tracks covered by solder mask. The fixed connection between the handle and the blade of the disposable version makes this type of scalpel a little bit more precise than the scalpel handle with exchangeable blades. Naughty people even cut through pins of ICs with scalpels to remove ICs without the use of a heat-gun, but you didn't read that here, as that dulls a blade pretty quickly and should only be used in a pinch.

Straight edged scalpels

ScalpelNo11.jpg

The sharp tip of this type of scalpel makes it ideal to cut the conductor track without nicking nearby tracks. The blade #11 has a short, straight edge that gives good control over the cut.

Round edged scalpels

ScalpelNo23.jpg

The copper tracks on the top layer of a PCB are usually covered with a layer of (green) solder mask, which can be carefully scraped away from the portions of the track that are about to be soldered to say attach a wire. The round shape of the blade #23 (there are other blades with a rounded edge) allows the user to only remove the solder mask from the track of interest, which will make the soldering process later on very easy, since the remaining solder mask will prevent the solder to stick to the covered tracks. Exposing the other tracks by scraping too much solder mask away may result in a much more difficult soldering job.

Soldering Flux

Soldering flux is the magic ingredient for a soldering job with many functions that makes it a breeze. It cleans and de-greases the components, promotes wetting (makes solder stick to the components instead of balling up) and reduces oxidation. The "tacky" variety also helps to keep the component in place so the usual step of "tacking down" a component can be skipped with enough soldering skill.

Soldering Fixtures / work piece holders

Soldering Fixtures for flat, smartphone sized PCBAs

Fix me

Work piece holders for PCBAs with large TH (through hole) components

Fix me

Magnification devices

Stereoscopic microscope (analog)

AmScope SM-4NTP

This stereo microscope has a lockable double arm boom stand and a magnification range of 7X to 45X (zoom) and is great for component level repairs / modifications. The boom stand allows to quickly change between the normal view onto the work piece in the soldering fixture and a side-view while holding the work piece in the hand without the need to touch the focus and magnifications settings. You just pull out the head over the edge of the table to have room to turn the work piece in the hand to be able to get a side-view of pin-less IC-packages or other things that are difficult to see in the normal view.

Fix me: add photos

Stereoscopic microscope (digital)

Fix me: add links and photos

The Stereo Ninja Project

Fix me: add links and photos