59
edits
Changes
Jump to navigation
Jump to search
|!'''Manufacturer Part Number'''|!'''Manufacturer'''|!'''Digi-Key Part Number'''|!'''Customer Reference'''|!'''Reference Designator'''|!'''Packaging'''|!'''Part Status'''|!'''Quantity'''|!'''Unit Price'''|!'''Extended Price'''|!'''Quantity Available'''|!'''Mfg Std Lead Time'''|!'''Description'''|!'''RoHS Status'''|!'''Lead Free Status'''|!'''REACH Status'''
→Option Bytes: Added alternate text to match FlashBash software options.
!Original Setting
|-
|Watchdog Reset on Halt(Reset On Entering Halt)
|Reset generation when entering HALT mode
|-
|Software (watchdog to be enabled by software)
|-
|Low Voltage Detection Selection(LVD Config)
|Highest Voltage Threshold
|-
The ST7 can be programmed using the RLINK-STD programmer. This programmer is available from Digi-Key https://www.digikey.com/en/products/detail/iotize/RLINK-STD/9923059
=== FlashBash Programmer ===
The FlashBash ST7 programmer claims to be able to program the ST7 on the LMS-6. This has not been evaluated yet. http://www.spen-soft.co.uk/
FlashBash V3 PCB can be ordered from DirtyPCBs.com: https://dirtypcbs.com/store/designer/details/1826/6489/flashbash-v3-st7-programmer
=== LMS-6 Card Edge Interface ===
LMS-6 Card edge interface board KiCad schematic and board layout: https://github.com/Reid-n0rc/LMS-6_Interface_Board
{| class="wikitable sortable mw-collapsible mw-collapsed"
|+LMS-6 Card Edge Connector Digi-Key BOM
|-
|885012207095
|}
====Interface Description and Theory of Operation====
The LMS-6 interface PCB allows the LMS-6 to be powered, connect to USB to UART, and connect to an in circuit programmer through the card edge connector.
{| class="wikitable"
|+Power Jumper Settings
! rowspan="2" |Jumper Ref Des
! colspan="4" |Jumpered Pins
|-
!Battery
!USB 5V
!Banana Jacks Regulated (J1&J3)
!Direct Power (J11&J12)
|-
|J2
|X
|2,3
|1,2
|X
|-
|J6
|1,2
|2,3
|2,3
|2,3
|-
|J10
|X
|2,3
|2,3
|1,2
|}
[https://github.com/Reid-n0rc/LMS-6_Interface_Board/blob/main/LMS-6_Interface_Board_Rev_10.pdf LMS-6 Interface Board Schematic Rev 10]
=====Circuit Power Options=====
The LMS-6 Inteface board offers four power options to power LMS-6. Components for any of the power options can be omitted if they will be unused to reduce the build the build cost.
======Battery Power======
The LMS-6 can be powered using three CR123 lithium batteries connected to the LMS-6 onboard battery holders. Batter power is enabled by jumpering Pin 1 and Pin to of J6 together.
======USB 5V Power======
The LMS-6 can be powered from the J4 Micro USB B connection. This is enabled by jumpering Pin 2 and Pin 3 of J2; Pin 2 and Pin 3 of J6.
USB power is indicated by D2 Green LED
=====USB to UART=====
The LMS-6 interface includes a FT-2232 USB to UART. UART1 is connected to GPS. The default baud rate for the GPS is 38400 bps. UART 2 TX is connected to U3 pin 19 on the LMS-6.
If the connections are wrong, they can swapped using JP1,JP2 and JP4, JP5.
=====In Circuit Programming=====
=====eFuse=====
<br />
==Reference==
Here are some reference materials. This is an initial population of material, and this section will need significant cleanup - putting links up for now.
